MIL-DTL-55181/5D
Inches
mm
Inches
mm
Inches
mm
Inches
mm
.002
0.05
.051
1.30
.220
5.59
.667
16.94
.005
0.12
.069
1.75
.221
5.61
.678
17.22
.010
0.25
.072
1.83
.233
5.92
.850
21.59
.015
0.38
.074
1.88
.241
6.12
1.111
28.22
.016
0.40
.076
1.93
.284
7.21
1.115
28.32
.026
0.66
.078
1.98
.339
8.61
1.178
29.92
.029
0.74
.081
2.05
.344
8.74
1.184
30.07
.034
0.86
.090
2.29
.378
9.60
1.250
31.75
.039
0.99
.100
2.54
.457
11.61
1.260
32.00
.041
1.41
.118
3.00
.516
13.10
1.378
35.00
.046
1.17
.125
3.17
.560
14.22
1.437
36.50
.047
1.19
.150
3.81
.637
16.18
1.468
37.28
.050
1.27
.156
3.96
NOTES:
1. Dimensions are in inches.
2. Metric equivalents are given for information only.
3. Unless otherwise specified tolerances are ±.005 (0.13 mm) inch for three place decimals and
±.01 (0.3 mm) inch for two place decimals.
4. Angular tolerances shall be ±30 minutes unless otherwise specified.
FIGURE 1. Dimensions and configuration - Continued.
REQUIREMENTS:
Dimensions and configurations: See figure 1and table I.
Contacts: 7.5 ampere current rating, 20 AWG.
Part or Identifying Number (PIN): M55181/5 (dash number as specified in table I).
TABLE I. Dash numbers, cross reference and mating connector table.
Cable size accommodation
Mating connector
1/
PIN
Type designator
1/
MIN
MAX
PIN
Type designator
M55181/5-01 MW10M(M)B11 .292 (7.42) .343 (8.71) M55181/6-01
MW20F(M)B00
M55181/5-02 MW10M(M)B13 .323 (8.20) .406 (10.31) M55181/6-01
MW20F(M)B00
M55181/5-03 MW10M(M)B17 .448 (11.38) .531 (13.48) M55181/6-01
MW20F(M)B00
M55181/5-04 MW10M(M)B19 .511 (12.98) .593 (15.06) M55181/6-01
MW20F(M)B00
M55181/5-05 MW10M(M)B15 .386 (9.80) .468 (11.88) M55181/6-01
MW20F(M)B00
1/ This type designator shall not be referenced for procurement purposes.
Changes from previous issue. The margins of this specification are marked with vertical lines to indicate
where changes from the previous issue were made. This was done as a convenience only and the
Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and
contractors are cautioned to evaluate the requirements of this document based on the entire content
irrespective of the marginal notations and relationship to the last previous issue.
3
For Parts Inquires submit RFQ to Parts Hangar, Inc.
© Copyright 2015 Integrated Publishing, Inc.
A Service Disabled Veteran Owned Small Business