MIL-DTL-55302/64H
Requirements:
Dimensions and configuration: See figure 1.
Material: Guide pins, type X guide sockets, jackscrews and jack sockets shall be made of corrosion resisting
stainless steel in accordance with ASTM A581 or ASTM A582 passivated in accordance with SAE-AMS-QQ-P-35
or shall be corrosion resistant copper nickel alloy (61 ±2% nickel, 2.5% max. other, and the balance zinc and shall
have a brinell hardness of 145 to 175. Type Y guide sockets shall be beryllium copper in accordance with
ASTM B196 or ASTM B197, nickel plated in accordance with SAE-AMS-QQ-N-290, class 2, 50 to 150
microinches.
Plating: The contact plating shall be in accordance with MIL-DTL-55302 or gold in accordance with ASTM B488
type II, code C, class 1.27, over nickel plating in accordance with SAE-AMS-QQ-N-290, class 2, 50 to 150
microinches in the engaging area and gold in accordance with ASTM B488 type II, code C, class 0.51, or type III,
code A, 0.51 over nickel plating in accordance with SAE-AMS-QQ-N-290, class 2, 50 to 150 microinches in the
termination area and gold in accordance with.
Contact identification: See figure 1.
Contact engagement and separation forces (number 22 contacts):
Minimum separation: 0.5 ounce.
Maximum engagement: 12.0 ounces for standard force and 4.0 ounces for low force.
NOTE: Low force contacts meet the requirements of standard force contacts.
Mating and unmating:
Standard insertion force contacts: The maximum mating force, in pounds, shall be the number of contacts
multiplied by 0.56 and the withdrawal force, in pounds, shall be a minimum of 0.08 times the number of contacts
and shall not exceed the measured insertion force.
Low insertion force contacts: The maximum mating force, in pounds, shall be the number of contacts multiplied by
0.25 and the withdrawal force, in pounds, shall be a minimum of 0.04 times the number of contacts and shall not
exceed the maximum insertion force.
NOTE: Not applicable when mating and unmating is accomplished through the engaging of turning jacksets.
Jackscrew and jack socket torque: 2-inch pounds maximum, fully mated.
Contact resistance: The average contact resistance of all contacts measured shall not exceed 0.010 ohm, and no
individual contact pair shall have a resistance exceeding 0.020 ohm.
Dielectric withstanding voltage:
Sea level: 1,000 volts rms.
High altitude: 300 volts rms.
Current rating: 5.0 amperes maximum in accordance with contact.
Polarization: Type X, regular, guide pin and socket, full round (see detail E). Type Y, adjustable "D" shaped guide
pin and/or socket (see detail G, and MIL-DTL-55302/57, detail B). All connectors are supplied in the -1 polarized
position. For other than OEM use, connectors may be repolarized by using M55302/57-01 spanner wrench and
M55302/63-01 guide pin and guide socket kit. When guides are removed and reinstalled in another position apply
Loctite 83-CV or equivalent to the threads. Ordering connectors in other than, the -1 polarized position may be done
by the OEM's by placing the desired polarized position in brackets three spaces after the Part or Identifying Number
(PIN) on the purchase order. Example M55302/64-A10Y [-32]. Polarization pins and sockets shall be adjusted to
any desired configuration by spanner wrench (M55302/57-01). Ordering connectors in the -1 polarized position
without Loctite 83-CV or equivalent applied may be done by placing a "-0" in brackets three spaces after the part on
the purchase order. Guide sets, as installed, shall withstand 7-inch ounces backoff torque applied through the guide
set mounting nut.
M55302/63-01 kit: Consists of one type Y "D" shaped guide socket and spanner nut and one type Y "D" shaped
guide pin and spanner nut (see detail G).
6
For Parts Inquires submit RFQ to Parts Hangar, Inc.
© Copyright 2015 Integrated Publishing, Inc.
A Service Disabled Veteran Owned Small Business