MS3190G
Barrel size |
Wire range |
A |
B |
C |
D dia |
E dia |
16 |
16-18-20 |
.345 (8.763) .341 (8.661) |
.079 (2.007) .073 (1.854) |
.048 (1.219) .044 (1.118) |
.042 (1.067) .036 (.914) |
.058 (1.473) .066 (1.676) |
12 |
12 - 14 |
.345 (8.763) .341 (8.661) |
.079 (2.007) .073 (1.854) |
.048 (1.219) .044 (1.118) |
.042 (1.067) .036 (.914) |
.102 (2.591) .098 (2.489) |
8 |
8 |
.520 (13.208) .510 (12.954) |
.094 (2.388) .084 (2.134) |
.048 (1.219) .044 (1.118) |
.066 (1.676) .060 (1.524) |
.184 (4.674) .179 (4.546) |
4 |
4 |
.520 (13.208) .510 (12.954) |
.094 (2.388) .084 (2.134) |
.048 (1.219) .044 (1.118) |
.066 (1.676) .060 (1.524) |
.256 (6.502) .279 (7.086) |
0 |
0 |
.675 (17.145) .665 (16.891) |
.094 (2.388) .084 (2.134) |
.048 (1.219) .044 (1.118) |
.066 (1.676) .060 (1.524) |
.458 (11.633) .451 (11.455) |
Barrel size |
Wire range |
F dia |
G dia |
J dia max |
K |
L dia |
16 |
16-18-20 |
.148 (3.760) .144 (3.658) |
.105 (2.667) .101 (2.565) |
.123 (3.124) |
.328 (8.331) .297 (7.544) |
.090 (2.286) .080 (2.032) |
12 |
12 - 14 |
.202 (5.131) .198 (5.030) |
.153 (3.886) .147 (3.734) |
.171 (4.343) |
.328 (8.331) .297 (7.544) |
.125 (3.175) .115 (2.921) |
8 |
8 |
.313 (7.950) .303 (7.696) |
.269 (6.833) .263 (6.680) |
.257 (6.528) |
.534 (13.564) .480 (12.192) |
.230 (5.842) .220 (5.588) |
4 |
4 |
.419 (10.643) .415 (10.541) |
.380 (9.652) .370 (9.398) |
.376 (9.550) |
.534 (13.564) .480 (12.192) |
.364 (9.245) .354 (8.991) |
0 |
0 |
.611 (15.520) .607 (15.412) |
.568 (14.427) .558 (14.173) |
.548 (13.919) |
.690 (17.526) .636 (16.154) |
.542 (13.767) .532 (13.513) |
NOTES:
1. Material, finish, and machined surfaces shall be as specified on the applicable procurement specification for the contact.
2. Dimensions are in inches unless otherwise specified.
3. All dimensions shown are for finished part after plating.
4. All diameters shall be concentric with each other within .005 total indicator reading (TIR).
5. See MIL-DTL-22520, MIL-C-22909 and MIL-C-39029 for the applicable crimping tool and the performance requirements of the crimped termination.
6. Finished parts shall have no sharp edges or burrs.
FIGURE 2. Dimensions and configurations, type B - Continued.
4
For Parts Inquires submit RFQ to Parts Hangar, Inc.
© Copyright 2015 Integrated Publishing, Inc.
A Service Disabled Veteran Owned Small Business