MS27488N
TABLE III. Metric equivalents.
Inch |
Millimeter |
Inch |
Millimeter |
Inch |
Millimeter |
Inch |
Millimeter |
0.010 |
0.254 |
0.115 |
2.921 |
0.404 |
10.262 |
0.872 |
22.149 |
0.020 |
0.508 |
0.120 |
3.048 |
0.414 |
10.516 |
0.822 |
20.879 |
0.038 |
0.965 |
0.125 |
3.175 |
0.416 |
10.566 |
0.841 |
21.361 |
0.045 |
1.143 |
0.130 |
3.302 |
0.431 |
10.947 |
0.990 |
25.146 |
0.048 |
1.219 |
0.135 |
3.429 |
0.438 |
11.125 |
1.021 |
25.933 |
0.058 |
1.473 |
0.160 |
4.064 |
0.500 |
12.700 |
1.071 |
27.203 |
0.066 |
1.676 |
0.165 |
4.191 |
0.596 |
15.138 |
1.139 |
28.931 |
0.069 |
1.753 |
0.170 |
4.318 |
0.606 |
15.393 |
1.189 |
30.200 |
0.079 |
2.007 |
0.175 |
4.445 |
0.755 |
19.177 |
1.391 |
35.331 |
0.080 |
2.032 |
0.273 |
6.934 |
0.791 |
20.091 |
1.422 |
36.119 |
0.090 |
2.286 |
0.275 |
6.985 |
0.796 |
20.218 |
1.441 |
36.601 |
0.100 |
2.540 |
0.283 |
7.188 |
0.805 |
20.447 |
1.472 |
37.389 |
NOTE: Metric equivalents (to the nearest 0.001 mm) are given for general information only and are based upon 1 inch = 25.4 mm.
REQUIREMENTS:
1. Material. Plastic rod, molded and extruded - temperature limit 200 °C minimum. The material used to fabricate sealing plugs shall be polytetrafluoroethylene (PTFE) in accordance with ASTM-D1710, or fluorinated ethylene propylene (FEP) in accordance with ASTM-D2116, or perfluoroalkoxy (PFA) in accordance with ASTM-D3307, or polyphenylsulfone (PPSU) in accordance with ASTM-D6394.
2. Color. Color of items shall be in accordance with EIA-359.
3. Resitivitity. Material resitivity shall be not less than 100 megohms when tested in accordance with ASTM-D257.
4. Installation. When installing sealing plugs in connector, component or module grommets, the head of the sealing plug shall be inserted first. The sealing plug is designed for use with an unwired contact installed in connector applications. The sealing plug shall be pushed into the grommet until the head is positioned against the end of the unwired contact.
5. Workmanship. The item shall be free from flash and burrs. The length of diameter B shall be free of all molding marks, protrusions, and blemishes. Molding marks, protrusions, and blemishes from gate cutoffs are permissible but only on the plug ends or side of the head and shall not be greater than 0.005 inch in height.
5
For Parts Inquires submit RFQ to Parts Hangar, Inc.
© Copyright 2015 Integrated Publishing, Inc.
A Service Disabled Veteran Owned Small Business